The Motley Fool Discussion Boards

Previous Page

Personal Finances / Credit Cards and Consumer Debt


Subject:  Re: update Date:  8/7/2013  2:44 AM
Author:  NoIDAtAll Number:  307154 of 312185

It was an enjoyable hobby for me. I sold some cars I wish I hadn't, among them my first car, a 1956 Chevy convertible.

Another car I liked was a 1964 MG Midget. I bought the car from an Insurance client for $75 - It didn't run and the body was pretty banged up, but solid. The guys daughter's boyfriend had an argument with the daughter and drove the P out of it, leaving the car parked parked on a street, after disconnecting the fuel line. I had it towed to my home, reconnected the fuel line, backed out of the driveway, shifted to first gear and drove about 3 ft before the transmission locked up... I backed up and drove forward another 3 ft, when it locked up again - I backed into the driveway and later pulled the engine and transmission - The car had a plate under the transmission, so I couldn't remove them separately. After removing the engine and transmission, I dismantled both. The insides of the transmission were in good condition, but the bearing flanges were wallowed out. I bought a used transmission with a sound case, but the synchronizers were badly worn, so I swapped the insides of the one into the case of the other - done, for $85, plus some sealant, lubricant and around 6 hours of rebuild time.

I went pretty cheap on rebuilding the motor - The was an arc on the crankshaft. I took it to a local machine shop to regrind... When I picked it up, there was a little bit of arc left on the journals, but I figured the machine shop knew what their work, and used it - I rebuilt the engine, installed the transmission on it, and put it back in the car... The engine started knocking after 75 miles. *sigh*

I pulled the engine and transmission, again, removed the transmission and clutch, disassemble the engine, took the crankshaft to the machine shop and asked for a refund, of the $25 they charged me to grind the crankshaft - I thought that a simple request, all things considered. The shop foreman refused the refund. I asked him why, and what else could have caused the motor to fail in such a short time frame - He responded, "Dirt"... I had cleaned the engine and its oil galleries pretty extensively, at a car wash, but not had it hot tanked. He had also checked the rods, found 2 bent and straightened them. I took the parts to a machine shop that machined engines for race cars. They machined the crankshaft and check the rods - found 2 still bent, and straightened them. I told them that I did not want to pull and rebuild the engine again, and asked if there was a way to assure that the rods were perfectly straight - Their reply was that they could ream out the old bushings, in the upper end of the rods, as the piston wrist pins floated in the upper end of the rods, rather than the pistons, in the particular motor, and then the lower and upper ends of the rods would be perfectly perpendicular. I axed them how much that would cost - $40. I asked if there was anything else they could do to assure that have to rebuild the motor again. They recommended balancing the motor (crankshaft, rods, pistons and flywheel), as doing so would "add to longevity." I asked how much - $80... I didn't blink an eye at accepting that - When I put it back together, it ran like a sewing machine.

I replaced the convertible top and installed new upholstery - pretty simple.

The owners of a body shop wanted to go on a vacation, and keep their accomplished sons out of trouble, so they charged them with straightening and repainting the car with a white acrylic enamel and black rocker panels, with a hardener that was impervious to bird droppings, bugs and tree sap, or eggs, for that matter. The car looked, ran and cornered exceptionally... The reason I sold it was that pickup trucks and SUVs tended to tailgate, at the level of my head, to an extent that could/would decapitate me.

That's some of my background, FWIW.

Copyright 1996-2018 trademark and the "Fool" logo is a trademark of The Motley Fool, Inc. Contact Us